USG shaft wall systems are non-loadbearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and the walls are finished later, along with interior partitions. Installation is quick and easy, using components and application procedures familiar to drywall contractors.

Our Shaftwall Metal Framing can be installed for vertical and horizontal encasement applications. With the help of a variety of mold, moisture, and fire-resistant gypsum and cement boards that

Walls. Solid Shafts. Horizontal Stud Shafts. Steel Framing. USG Steel section of shaft wall is needed for a single vertical pipe.

Technical Support 1-800-USG-4YOU Product Safety Hotline 1-800-507-8899 Product Categories

This SHAFT WALL SYSTEM DETAIL must not be used without a complete evaluation by the owner's design professional to verify the suitability of the design for a given structure. 1" SHEETROCK BRAND LINER PANELS USG STEEL 2" H STUD 3 4" AIR SPACE (MIN.) 1" SHEETROCK BRAND LINER PANELS 3 1/2" LINE OF ADJACENT FRAMING MIN. STEEL 6" C-RUNNER 20 GA.

USG Fire Resistant Assemblies Wall Penetration Details (English) - J2133 SECTION PLAN USG SHEETROCK ©BRAND FIRECODE CORE GYPSUM PANELS USG SHEETROCK FIRECODE ® COMPOUND PIPE COVERING AND THROUGH PENETRATION WALL ASSEMBLY Scale: 3" = 1' - 0" SYSTEM NO. W-L-5044 9

A 2-hour fire-resistive, non-load bearing non-combustible partition designed to enclose shaftwalls, containing elevators, ducts, piping, air shafts and similar construction applications. System consists of 1" shaftliner panels supported by 2-1/2", 4" or 6" C-T studs and faced on one side with two layers of 1/2" Type C or 5/8" Type X gypsum board.

USG Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in 

USG Shaft Wall Systems - CEMCO

USG SHEETROCK ©BRAND SHAFT LINER GYPSUM PANELS, CUT TOP OF PANEL 1" LESS THAN FLOOR TO CEILING HEIGHT, TYPICAL Scale: 3" = 1' - 0" HEAD OF WALL UL HW-D-0611 (1 AND 2 HOUR) 7 USG SHEETROCK © BRAND FIRECODE CORE GYPSUM PANELS, CUT

SHEETROCK brand shaft wall systems have been comprehensively tested for 1- to 4-hour fire resistance ratings (UL Design No U415) only when all of the system 

5. For more details and construction methods, refer to UL Design #U415 System A and the USGinstallation instructions. Two-Hour Cavity Shaft Wall (Non-Load Bearing), See Figure 2 1. A minimum 2-1/2-in deep 24 gauge floor and ceiling J-runners, attached to

Shaftwall systems are nonload-bearing fire rated wall assemblies that provide critical, life safety, fire-resistant protection for elevator shafts, 

USG Shaft Wall Systems are non-load bearing gypsum wall partition assemblies constructed from outside the shaft at each floor.

Mill Steel Framing is a licensed manufacturer of the USG Shaft Wall system. USG Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies 

USG Middle East Shaftwall Access Panel - Heavy Duty is ideal for for shaftwall, plum walls and brick wall installation, comes with mounting claws for simple wall installation. Add To Favorites Add to Compare Heavy Duty Shaft Wall Wet Area Size Product Identifier Qty Order Sample Add To My Project List Performance Specifications Product Items

USG Architectural Services Thin, Lightweight Design The shaft wall is completed by installing one or more layers of Firecode GWB.

Technical Support 1-800-USG-4YOU Product Safety Hotline 1-800-507-8899 Product Categories

Design Your System 23 Design Details Good Design Practices Specify Your System 36 Application Guide Specifications For More Information Technical Service 800 USG.4YOU Websites usg.com usgdesignstudio.com 4 USG Shaft Wall Systems shaft at

details on page 24. WALLS CEILINGS USG Shaft Wall Systems | 6 COMPONENTS USG Shaft Wall Systems have been comprehensively tested for ire resistan ce ratings only when all of the

USG Shaft Walls provide up to 4-hour fire resistance and sound ratings to 51 STC. They resist intermittent lateral loads up to 15 psf; also resist fatigue 

Gyprock Shaft Systems are not suitable for certain walls of Class 9B buildings which require 1.0kPa loading. Resistance to Impact A series of impacts from a 27.2kg sandbag are imposed on a typical wall section and must not cause permanent damage.

Shaft Wall-AER-09038 SCALE: DATE: UNITED STATES GYPSUM COMPANY This Shaft Wall Detail must not be used without a complete evaluation by the owner's design professional--to

USG Shaft Wall Systems are non-load-bearing gypsum wall partition asse mblies constructed from outside the shaft at each loor. Shafts are enclosed early in construct ion, and the walls are inished later, along with interior partitions. Installation is quick and ea sy, using components and application procedures familiar to drywall contractors.

Design Your System 21 Design Details Good Design Practices Specify Your System 33 Application Guide Specifications For More Information Technical Service 800 USG.4YOU Websites Use USG shaft wall systems to construct elevator shafts, mechanical shafts, stairwells, air return shafts and horizontal membranes. These shafts are

Use CGC Shaft Wall Systems to construct elevator shafts, mechanical shafts, stairwells, air return shafts and horizontal membranes. These shafts are vital for vertical communication, power, water, fresh air, exhaust and a means of egress. Solid Shafts Horizontal Stud Shafts