Product Overview. Turning Grade Map. Turning Grades. P Steel. M Stainless steel. K Cast iron. N Non-ferrous. S Superalloys. P10 P20 P30 P40. M10 M20 M30.

TAEGUline cutting tool grades are classified according to application and type of Cermets are very hard grades made of solid Titanium Carbide or Carbon 

Nominal Properties and Applications of Standard Grades Grade Percent Cobalt Grain Size Hardness, Rockwell A Properties Applications HC-UF12 . 12.0 . Ultra Fine : 92.5 . Excellent Wear Minimal Impact Hydro Carbide, Inc . ∙ 4439 Route 982 ∙ Latrobe, PA 15650 ∙ Phone: 800-245-2476 ∙ . www.ramet.com. ∙ www.hydrocarbide.com 05/

General Carbide Corporation 1151 Garden Street n Greensburg, PA 15601 TEL: 800.245.2465 n 724.836.3000 FAX: 800.547.2659 n 724.836.6274 [email protected] SETTING THE STANDARD FOR EXCELLENCE IN TUNGSTEN CARBIDE TOOLING General Carbide is a vertically integrated manufacturer of finished tooling

Mitsubishi Grade Chart - Carbide Depot grades-comparison-table-mitsubishi-carbide 1/2 Downloaded from datacenterdynamics.com.br on.

Carbide Grades & Specifications 1 Carbide Grade K60X K50X K40XF DK007T (DK2457UF) DK400N DK120 DK460UF K40UF DK500UF K44UF DK255UF K20F K88UF DK256EH DK502UF

11040 Parker Dr., WCIDC IV Irwin, PA 15642 412-751-6900 1-800-544-4338 FAX 412-751-4824 Visit our Web site: www.innovativecarbide.com INNOVATIVE CARBIDE GRADE COMPARISON

A comprehensive stocked range of grades in carbide plate blanks for mold and die materials, as well as carbide rods for drill or reamer materials. Grades D AF1 Ultra-fine grained Carbide With grains finer than that of conventional grades, an excellent balance of high toughness and high hardness as well as superior edge sharpness is achieved.

See Page 4 for More Information on Horizon Carbide Grades These are Approximate Grade Conversions. Bold Type = Standard Horizon Grades and Competitive Equivalents. HORIZON CARBIDE TOOL, INC. (480) 968-0957 FAX (480) 968-8042 [email protected] HorizonCatalog-2002-Rev.pdf Author: briant Created Date:

This range of Cemented Carbides can be subdivided into its major application areas as follows: The grades with binder contents between 6- 30% and grain 

HB-115. High wear, low to medium impact, micro grain size grade, for cutting tools, dies, knives, punches, roughing tools, will withstand slight shock, 

GRADE COMPARISON TABLE. CEMENTED CARBIDE. (Note) The above table is selected from a publication. We have not obtained approval from each company. Classifi-.

RT 100 XF High Performance Carbide Drill: Key Product Lines; RF 100 Speed End Mills: RF 100 90° End Mills: RF 100 Diver End Mills: SELECTMILL End Mills: RF 100 Sharp: Key Product Lines; Powertap Taps: Carbide Grades. Download. Was this page helpful? Yes No. Products. Drills. End Mills. Taps. Thread Mills. Grooving Systems. Reamers. Tool

MT Grade Symbol WC Co TiC Ta(Nb)C Ni Cr3C2 Other Average Size µm Ultra-fine <1 Submicron ≤ 1 Fine 1 - 3 Medium 3 - 5 Coarse ≥ 5 Hardness HRA MT-106 94 6 2 fine 350 14.95 91.7-92.4 General Purpose MT-206 94 6 4 medium 350 14.95 90.5-91.5 MT-210 90 10 4 medium 425 14.60 89.0-90.0 Metal Forming, Wear and Impact MT-212 88 12 4 medium 425 14.30

CEMENTED CARBIDE (Note) The above table is selected from a publication. We have not obtained approval from each company. Classifi-cation: Symbol: Turning: Milling: Mitsubishi: Materials

CEMENTED CARBIDE GRADES COMPARISON TABLE (Note) The above table is selected from a publication. We have not obtained approval from each company. ISO Mitsubishi Carbide Sumitomo Electric Tungaloy Dijet Tool Kennametal Seco Tools Classifi- Iscar cation Symbol Turning Milling. Z Z01 SF10 MF07 MF10 F0 F MD05F MD1508 FZ05

A Insert Grades Insert Grades A1~A20 Turning A2~A3 Small Tools A3 Grooving A4 Cut-Off A4 Drilling A5 Milling A5 Cermet A6 PVD Coated Cermet A6 CVD Coated Carbide (Turning) A8 PVD Coated Carbide (Turning) A10 PVD / CVD Coated Carbide (Milling / Drilling) A12 Carbide A14 DLC Coated Carbide A14 Ceramic A15 CBN (Cubic Boron Nitride) A16 PCD (Polycrystalline

Compare ANC grades to all major suppliers of carbide cutting tools. 6. Chip Control Comparison Charts.... Compare ANC insert chip control configurations 

Phone: (800) 331-7585 Fax: (281) 255-9333 www.anconline.com American National Carbide Delivering Carbide Value GRADE COMPARISON CHART – CVD COATED GRADES (ISO CLASS

452 rows · Get full information on any Carbide Grade. Including Cutting Speeds, Compatible

As indicated on the properties chart,. Kennametal has a wide variety of carbide grades including fine, medium, and coarse grained tungsten carbides with cobalt 

CUTTING TOOLS - CARBIDE INSERTS CARBIDE INSERTS STAR TOOL SUPPLY / GRAND TOOL SUPPLY Tel: 201-518-8461 / Fax: 201-596-3427 650 Huyler St / So. Hackensack, NJ 07606 USA SERIES 156: "A" SHAPES Order No. 0120351 0120361 0120371 Price Insert Style Grade ADKT Dimensions in inches and (mm) ADKT 85 DEG., PARALLELOGRAM, POSITIVE RAKE WITH MM

Product comparison by chipbreaker. Grade Ultra-fine-grain cemented carbide coated with TiN-based compound User's Guide- Grade Comparison Chart 

Federal Carbide Company • One Eagle Ridge Road • Tyrone, Pennsylvania 16686 USA 814-684-7600 / 800-631-3640 Fax: 814-684-9400 • [email protected] • [email protected] • www.federalcarbide.com

Grade Average Density (g/cm3) Rockwell “A” Hardness (average) Grain Size WC Co NI TaNbC OTHER Composition values may vary +/- 1%. The Company reserves the right to change,

carbide grades are available the request and detailed information can be hold at www. Excellent Wear, can Impact. The flake is compacted under high pressure to bloom a miracle with chalklike consistency. It offers superior abrasion and corrosion resistance. Deposition on in a coated insert of finish grade highly resistant to deposition.